Search results for " finite element modelling"
showing 7 items of 7 documents
Simplified equivalent finite element modelling of concrete-filled steel tubular K-joints with and without studs
2022
Concrete Filled Steel Tubular (CFST) K-joints employed for truss structures gained high interest in the last years due to their widespread use in engineering practice. The overall performances of these joints can be efficiently improved by using steel studs welded in the inner surface of the steel chord filled with the concrete, avoiding punching shear failure, and improving the overall strength and ductility. However, a reliable prediction of the structural behavior of the joints is outmost of importance for the assessment of the capacity of new and existing structures, and there are no standardized design methods nowadays. In this paper, the structural performances of CFST K-joints with a…
Dissipative connections of rc frames with prefabricated steel-trussed-concrete beams
2020
In the last thirty years, Hybrid Steel-Trussed Concrete Beams (HSTCBs) have been widely used in civil and industrial constructions and, therefore, their mechanical performance must be evaluated with the aim of guaranteeing adequate dissipation of the seismic energy particularly in the beam-to-column joints. However, one of the most frequent peculiarities of HSTCBs is that of using their own steel joist to cover large spans with reduced depth and, in the case of traditional beam-to-column connections, this requires large amount of steel reinforcement inside the panel zone, often made with large diameter rebars. These characteristics make both the panel zone and the beam end potentially vulne…
Finite element modelling of slipage between FRP rebar and concrete in pull-out test
2014
The paper presents numerical results of direct pull-out test of glass fiber-reinforced polymer (GFRP) rebars embedded in concrete. Rebars of three different cross-sections are considered: circular without longitudinal ribs and with two and four ribs. The design analyses of the rebar configurations embedded in concrete are investigated by the 3D finite element method (FEM), which takes into account the non-linearity using ANSYS software. The results of the numerical model with two ribs were compared with the experimental results. Then, the effect of different rebar geometries to the load-slip pull-out curves was studied. It is concluded that the influence of rib height and width on the pull-…
Numerical modelling of the tensile behaviour of BFRCM strips
2019
This paper aims at investigating the tensile behaviour of basalt fibres on cementitious matrix for the strengthening of masonry structures. The use of Basalt Fibre Reinforced Cementitious Matrix (BFRCM) is favourably considered by the scientific community because it represents a natural composite material with high compatibility with stone and masonry substrate. The study is developed through the generation of Finite Element (FE) models capable of reproducing the tensile behaviour of BFRCM strips with different number of layers of grid. For the scope, the micro-modelling approach is adopted assuming different levels of detail for the simulation of the interface constitutive behaviour. Fibre…
Influence of wall-to-floor connections and pounding on pre- and post-diction simulations of a masonry building aggregate tested on a shaking table
2023
AbstractThis paper presents numerical simulations within the frame of the project SERA—AIMS (Seismic Testing of Adjacent Interacting Masonry Structures). The study includes blind pre-diction and post-diction stages. The former was developed before performing the shaking table tests at the laboratory facilities of LNEC (Lisbon), while the latter was carried out once the test results were known. For both, three-dimensional finite element models were prepared following a macro-modelling approach. The structure consisted of a half-scaled masonry aggregate composed by two units with different floor levels. Material properties used for the pre-diction model were based on preliminary tests previou…
Numerical simulations of the mechanical characteristics of glass fibre reinforced C-profiles
2006
A mechanical characterisation analysis on pultruded glass fibre reinforced C-shaped profiles, developed as modular construction elements to assemble fastening systems, such as doors, window frames and shutters is presented. The key idea is to perform the analysis, and all the related identification procedures of the material parameters, via a coupled approach, based on a limited number of standard laboratory tests and on the numerical finite element simulations of the same tests. The proposed approach allows one to identify all those material parameters which are difficult to detect, by means of simple laboratory experiments on specimens that are extracted from commercial products. It also …
Simulation of blind pre-diction and post-diction shaking table tests on a masonry building aggregate using a continuum modelling approach
2023
AbstractMasonry buildings of historical centres are usually organized within aggregates, whose structural performance against seismic actions is challenging to predict and constitutes still an open issue. The SERA—AIMS (Seismic Testing of Adjacent Interacting Masonry Structures) project was developed to provide additional experimental data by testing a half-scale, two-unit stone masonry aggregate subjected to two horizontal components of dynamic excitation. In this context, this paper investigates the reliability of the modelling approach and the assumptions adopted to generate a three-dimensional continuum finite element model. The work involves two stages, namely a blind pre-diction and a…